Miscellaneous Update

Not much progress as far as assembly goes...but...lots of parts acquisitions and some dash/gauge progress (thanks to Doug!). First, current assembly state.

This is the rough order of what I have to do to get the car back on the road (feel free to object/correct/suggest through comments!)

1. Finish assembling the tranny (top cover/OD/nose)
2. Pull already rebuilt TR6 engine from TR6 and put front plate & sump from 2500 on.
3. Marry up engine/clutch/tranny
4. Clean up and repaint underhood area (means deciding color for car, see below)
5. Mount engine/tranny from underneath
6. Re-install already rebuilt front suspension
7. Install driveshaft coming from California (a deal I couldn't refuse, was planning on making one up)
8. Turn used Stag rotors, rebuild Stag calipers and install front brakes
9. Replace rear shoes/wheel cylinders/drums as necessary (have all 3 new)
10. Replace flex brake lines
11. Modify Mk. II RHD gas pedal to fit LHD Mk. I (may be interesting...)
12. Coat fuel tank with liner after shaking chain for a while to break loose crud & clean
13. Reinstal fuel tank and refurbished sender (thanks Doug!)
14. Have radiator re-cored for increased cooling, because...
15. the next step will be to install the new heat/A-C system (R-134) that Dave and I are designing
16. Mount master cylinders/slave cylinder (have all new or rebuilt) and connect/fill/bleed/fill/bleed/fill/bleed/etc...hydraulics (DOT5, I'm not going racing)
17. Rebuild HS 6 carbs (have kits) and install w/exhaust manifold
18. Trailer to local custom exhaust shop for fabrication/installation
19. Reinstall front seats and install new seat belts front and rear (already have)
20. Cover split vinyl on top of dash and install new dash center/gauges/radio/etc
21. Debug electricals (this could take weeks...I've never even hooked up a battery at this point)
22. Debug engine/mechanicals (if there is a major risk here, it's the differential/halfshafts, I'll look at the halfshafts while underneath and do U-joints if needed, but I'm not touching the diff...car had 57k miles so I'm trusting it's OK)
23. Any minor interior cosmetics
24. Blast TR6 wheels, paint, buy/mount/balance tires
25. Replace center emblem in TR6 centers and install
26. Install new wiper arms/wipers (already have)
27. Install bumpers
28. I'm sure there's stuff I'm forgetting, I reserve the right to edit this post!
29. Install child seat and let's go Triumphing!

Now, as to color choices. As previously posted, I just can't get into the green and red combination. Since I have a new red carpet set that came with the car, and the front seats are largely newly reuplolstered in red...and the rear seat is still in original red leather...I think I'm stuck with a red interior for the forseeable future. I'm thinking that leaves me with a limited selection of colors, especially since the body has some waves....so right now the leading candidate is a two tone combo of red roof/off-white body, using period colors. What do you think?

Parts...I've gotten a lot since my last post. For example, a NOS 2500 O/D shift lever (eBay), a pair of sidelight lenses (a kind-hearted British saloon enthusiast), speedo cable, NOS bumper overriders, Lucas Square 8 driving lights, front wheel bearings, strut gaiters, u-joints, rear window heater kit, lug nuts, tie rod ends, side mirrors (all eBay) have all found their way into the garage.

Finally, here's some of the work Doug's been doing on the gauges and dash. He's found that the triple gauge I purchased (supposedly from a later 2000) isn't exactly the same as the original, so we're going to have to create a voltmeter from another gauge. The pictures explain it better than I can, but I can't get it to load tonight. So I guess that will have to wait for next time!